1948 Cadillac Series 76 Stock Front Suspension Diagram
SEARCH
VW Car Fault Codes DTC - Polo, Passat, Touareg, Tiguan, Golf, Crafter, Transporter T5, Sharan, Jetta
VW Engine malfunctions
B2AAA General error code. This combination appears in the presence of other faults.
P10A4 Malfunction of the intake flap
P10A9 Malfunction of the electromagnetic clutch of the compressor device
P175D Spontaneous opening in the operation of the clutch system. Most likely, the disk is worn out.
P130A Malfunction in one of the cylinders, damage to the device
P2BAC USR valve malfunction, arbitrary device shutdown
P2BAB Nitric oxide limit exceeded, valve EGR shutdown
P242F The control unit reports restrictions associated with the particulate filter
P10A900 (P10A9) Malfunctions in the operation of the throttle valve actuator
P261A Code P261A or P261A00 is a result of damage to the electrical circuit of the ventilation, heating and air conditioning system
P0016 Codes P0016 and P001600 indicate the incorrect relative position of the motor shafts. To solve the problem, a detailed diagnosis of the integrity of the gears on the pulley will be required. Perhaps the cause of the malfunction is a mismatch in the labels.
P0068 Literally, the error is translated as "the deviation of the angle of advance of the throttle". A malfunction leads to improper intake air pressure.
P0069 The control unit detected an incorrect ratio in the intake air pressure
P0087 Code P0087 indicates a decrease in pressure in the fuel system.
Possible causes of the malfunction:
- damage to high or low pressure lines;
- damage to connectors or electrical harnesses;
- wear of a pusher fuel filter of a high pressure;
- nozzle clogging;
- malfunction of the fuel system controller;
- failure of the pressure control valve.
P0108 The control unit reports an incorrect pressure fixed at the inlet. It is recommended to check the operation of the device G71 and F96, from one of them the wrong signal is sent to the microprocessor.
P0121 Code P0121 appears as a result of an incorrect pulse from the throttle potentiometer G69
P0171 Codes P0171 or P017100 appear as a result of depletion of the air-fuel mixture. Defect found in the first row of cylinders.
P0172 Combination 0172 results from the enrichment of the air-fuel mixture in the first row of cylinders
P0299 Code P0299 or P029900 indicates a reduced boost pressure.
When this malfunction occurs, the following symptoms appear:
- on the control combination, the Check indicator lights up;
- the inclusion of a speed limiter up to 40 km / h;
- the power of the power unit is significantly reduced;
- noise appears in the operation of a turbine or compressor on a diesel engine.
The reasons that led to this error:
- reduced pressure of the engine fluid in the power unit;
- failure of a turbine or discharge device;
- malfunctions in the EGR system (EGR);
- clogged air filter or air intake in the intake manifold;
- breakdown of boost pressure controller.
P0300 Code P0300 appears as a result of fixing the misfire in one of the engine cylinders. A specific number is not indicated, so you have to search for the cause yourself.
P0301 Combination P0301 reports misfire in the first cylinder of the engine.
Symptoms that may occur with such a malfunction:
- the difficulty of starting the power unit;
- "Triple" of the engine, unstable engine idling;
- random stop of the engine when idling, at traffic lights or in traffic jams.
P0302 The combination P0302 appears as a result of the appearance of misfire in the second cylinder
P0303 Code P0303 indicates misfire in the third cylinder of the car engine.
P0304 Misfire Detected in the fourth engine cylinder
P0354 Malfunction of the fourth cylinder of the engine, the problem may be a malfunction of the ignition control system
P0401 Code P0401 appears when the throughput in the exhaust gas recirculation system is reduced. This combination may be due to wear of the sensors, as well as air leaks.
P0403 Code P040300 appears as a result of a malfunction in the exhaust gas recirculation valve. This refers to the device N18. The appearance of code P040300 may be due to a violation of the tightness of the system, as well as a malfunction of the control unit.
P0404 Incorrect control range in the exhaust gas recirculation system
P0411 Code P0411 indicates a decrease in throughput in the operation of the secondary air supply system
P0420 The combination of P0420 appears as a result of reduced efficiency in the operation of the catalyst system located in the front row. It is necessary to check the tightness of all components and pipes. Damaged lines must be replaced, and weakened clamps are tightened.
P0441 Code literally stands for "incorrect flow in the system for monitoring the removal of fuel vapor"
P0455 Microprocessor module detected a serious leak in the fuel tank ventilation system
P0456 Code P0456 reports a minor leak in the fuel tank ventilation system
P0491 Code P0491 appears as a result of reduced throughput of the secondary air supply system. The fault is recorded in the front row.
P0507 Engine idle above maximum
P0638 Invalid signal from throttle control module
P0726 Invalid signal received by the microprocessor about the engine speed
P0734 Wrong gear ratio in fourth speed
P0811 Error P0811 with severe slip of the clutch in the clutch system. Detailed diagnostics of all elements of the node, including disk integrity, is required.
P1031 The nominal value of the readings from the valve of the dampers located on the intake ducts is not reached.
P1065 Code P106500 indicates an incorrect fuel pressure control range
P1114 The appearance of code 1114 indicates an increased internal resistance of the second probe installed in the first row
P1127 Re-enrichment of the mixture in the first row of cylinders Under the load of the power unit, its adaptation does not pass.
P1136 On thePassat B5 2008 and other models, this code indicates the depletion of the combustible mixture in the first row of engine cylinders. The specific number must be verified by the diagnostic method. The control unit indicates that this malfunction occurs when the engine is idling.
P1141 Invalid load accounting data
P1152 Re-depletion of the mixture in the first row of cylinders The problem is related to problems with adaptation.
P1165 Code 1165 appears as a result of re-enrichment of the mixture in the first row of cylinders
P1248 Incorrect control range in the injection timing control system
P1250 Too low fuel level in the tank
P1263 Invalid signal from the second cylinder injector pump valve.
P1273 Code 1273 appears when you exit the control range of the signal coming from the valve of the pump nozzle of the fifth cylinder
P1296 Malfunction in the cooling system. The reasons for this error can be many:
- breakdown of one of the antifreeze temperature sensors (disconnecting the connector, contact oxidation, wire damage);
- lack of refrigerant in the expansion tank;
- boiling antifreeze, leading to overheating of the power unit;
- lack of tightness associated with damage to the nozzles;
- errors in the functioning of the control unit;
- malfunction of the thermostat or its incorrect operation.
P1297 Pressure drop in the pipe between the turbocharged unit and the throttle body
P1403 On the Volkswagen Passat CC with a gasoline engine and other cars, this code indicates a violation of the control range in the exhaust gas recirculation system.
P1423 Too low throughput in the secondary air supply system, fixed in the first row of cylinders
P1479 Code P1479 indicates a mechanical failure of the brake booster vacuum system
P1545 Malfunction of the throttle control system
P1553 The literal translation of the error is "incorrect ratio of the height and pressure controller signals in the intake manifold." With this problem, engine malfunctions may occur.
P1562 The error is literally translated as "fuel pump dispenser-N146: upper limit"
P1582 Upper adaptation limit reached in idle control
P1570 The combination P1570 can be literally interpreted as "blocking the engine control unit". Most likely, the cause of the problem is associated with a regular immobilizer.
Possible malfunctions:
- breakdown of the control module by the motor blocker;
- damage to the immobilizer antenna;
- chip malfunction;
- damage to the wiring, oxidation of the contacts on the connector;
- the use of auto-start alarms, which led to a conflict between the standard immobilizer and the additional one.
P1601 Invalid signal coming from the power relay terminal 30-J317
P1649 Code P1649 indicates the absence of messages from the control module anti-lock system. The cause of the problem may be the data bus. It is required to check the loop on the ABS control unit (ABS) and the microprocessor module.
P1951 The second fan of the cooling system V177 is blocked or its operation is difficult. The cause of the problem may be the poor contact of the device with the on-board network, as well as damage to the wiring. Sometimes a malfunction is oxidizing the contacts on the connector.
P2002 Code 2002 appears as a result of a malfunction in the diesel particulate filter mounted on the first row of cylinders. The device must be replaced since it is not practical to clean it.
P2015 Code P2015 indicates malfunctions in the intake manifold flaps
P2096 The combination indicates an excess of the depletion limit of the air-fuel mixture. The problem, most likely, is the oxygen controller installed after the catalyst in the front row.
P2097 Oxygen controller mixture enrichment control limit exceeded. It is necessary to check the sensor installed in the first row after the catalyst.
P2101 Malfunctions in the operation of the throttle
P2150 Injector Power (s) V: Short to Ground
P2177 Code P2177 indicates a lean mixture in the first row of engine cylinders when it is idling
P2187 A lean mixture in the first row of the engine cylinders when idling
P2004 Code P2004 reports that the intake flaps of the first row of cylinders do not close
P2179 lean mixture in the cylinders of the power unit at speeds above idle
P2181 Code 2181 indicates a malfunction in the cooling system. This is a common mistake, so the user needs to diagnose all components of the node.
P2192 On a car with a turbodiesel, this code often appears when enriching the air-fuel mixture. The control unit indicates that the problem may be a malfunction of the first oxygen controller installed in a row of 1 cylinders.
P2261 Mechanical damage turbocharger bypass N249
P2262 No turbocharger pressure detected, mechanical failure
P2263 Turbocharger malfunction
P2279 Code P2279 indicates a leak in the intake system. It is necessary to check all the lines, as well as their connection. Possible weakening of the clamps or damage to the nozzles.
P2463 Particulate filter problem. If error P2463 is most likely, the filter element will have to be changed.
P2637 Code P2637 indicates an incorrect torque pulse of the power unit A
P3014 Code 3014 or 014 indicates a short to ground or damage to the wiring of the second boost pressure control valve N274.
P3078 The combination indicates problems in the operation of the throttle control unit. When the power unit is idling, the air supply to the cylinders is insufficient.
P3081 Code 3081 onTuareg 32 and otherVolkswagen models indicates a low engine temperature. The causes of the malfunction can be many, but you need to start the diagnosis with the quality of antifreeze and the efficiency of the thermostat.
P3129 The basic settings of the mechanical stop of the intake flaps in the closed position have been violated
P3139 Code 3139 reports that the pulse from the inlet flap is out of range
P3192 OnVWs T4, T5 and other data versions, the code indicates a malfunction in the intake manifold flaps. The control unit calculated the violation of the basic parameters of the installation of the mechanical stop in the closed position.
VW Timing Malfunctions
P000A Timing is too slow. The cause of the problem, most likely, is the extension of the timing chain. It is necessary to check the integrity of the product and replace it if necessary.
P0010 Code 0010 indicates a malfunction in the valve timing
P0011 Code P0011 is literally translated as "the nominal value in the shift of the valve timing to the earlier side has not been reached." It is required to check the integrity of the shaft pulleys, as well as the timing chain.
P0025 Code 0025 appears when the valve timing is shifted to an earlier side. The problem is fixed in the second row. The control unit reports that the nominal value has not been reached, which led to an error.
P1049 Short to ground in the power circuit of the exhaust valve timing control valve. Detailed diagnostics of N318 devices are required.
P1527 Code 1527 appears as a result of a short to ground in the valve timing circuit.
Faulty VW crankshaft and camshaft controllers
P0322 Code P0322 indicates a malfunction in the crankshaft position sensor, the possible causes of the problem:
- failure of the controller itself;
- damage to the wiring through which the sensor is connected;
- clogged connector or oxidation of contacts on the block;
- moisture on the plug;
- malfunction of the control unit.
P0341 Damage to the camshaft sensor
P0346 Incorrect signal or failure of the camshaft position sensor. The user needs to diagnose the G163 device.
P1338 Code 1338 appears as a result of a short circuit to a positive terminal or a break in the wiring of the camshaft position sensor. This refers to the controller installed in the front row.
P3007 Code 3007 indicates the absence of a signal from the camshaft position controller G40
16725 Incorrect signal coming from the camshaft position controller.
Possible causes of the problem:
- malfunction of the wiring supplying the sensor;
- moisture entering the cable connector that is connected to the controller;
- failure of the device itself;
- damage or oxidation of contacts on the sensor block;
- cable wear.
16726 The reduced signal level coming from the camshaft position controller. The user needs to check the operation of the G40 device.
16727 The increased signal from the camshaft sensor
17748 Signal mismatch between camshaft and crankshaft position controllers (G40 and G28, respectively).
VW Malfunctions in the work of electricians and electronics
P072B The number of attempts to reverse gear has been exceeded. The error is typical for DSG robotic transmissions.
P072C Gearbox system locked in first gear
P202B Short to ground in the tank heater circuit
P0000 The combination appears at the end of the display of trouble codes on the display
P0001 Open control wiring of the fuel supply controller. It is necessary to check the contacts on the chip with the cable and eliminate oxidation, if any.
P0003 On Volkswagen B, VR6, and other models, code 0003 appears when the voltage coming from the fuel supply sensor is reduced.
P0030 Open or damaged electrical circuit of the heating system
P0033 Malfunction in a circuit of the bypass valve of a turbocharger
P0047 Code P0047 indicates a malfunction in the solenoid valve control boost
P0078 Code 0078 appears when the wiring is damaged by exhaust valves
P0098 Increased signal coming from the second intake air temperature controller
P0102 The combination P0101 (0102) appears as a result of a reduced signal coming from the G70 mass air flow sensor. The cause of the problem may be poor contact or damage to the wires. If the flowmeter is clogged, you can try to clean it using a special tool for the carburetor. In case these actions did not help to solve the problem, the device changes completely.
P0104 No signal from the mass air flow sensor
P0116 The control unit receives an invalid signal from the engine coolant temperature controller
P0183 Damage to the power line or short circuit to plus fuel temperature controller G81
P0190 Damage to the power line or short circuit of the contacts on the wiring of the fuel pressure sensor G247
P0196 Incorrect signal coming from the engine fluid temperature controller. This refers to the G8 sensor.
P0200 Code indicates a failure or damage to the electrical circuit supplying the engine nozzle
P0201 Failure or damage to the electrical circuit supplying the nozzle of the first cylinder
P0204 Failure of the electrical circuit supplying the nozzle of the fourth cylinder. A detailed check of the N33 device is required.
P0222 Incorrect signal from the angle of rotation control of the second throttle actuator
P0236 Codes P0236 or P023600 reports an invalid signal from the boost pressure controller
P0238 The combination of P0238 indicates an increased signal coming from the boost pressure controller
P0243 Open circuit or short to ground in the boost valve solenoid valve
P0332 Low pulse level detected in the electrical circuit of the second knock controller G66
P0343 Increased pulse coming from the camshaft adjuster. The user needs to test the operation of the G40 controller in detail.
P0407 Reduced signal from the exhaust gas recirculation potentiometer
P0444 On Golf 4 and other Volkswagen, the combination 0444 indicates an open circuit in the valve of the first adsorber
P0513 Invalid engine lock code. It is necessary to check the operation of the immobilizer, including the diagnosis of its contacts and electrical circuits.
P0544 Malfunction or damage to the electrical circuit of the exhaust gas temperature controller G235
P0546 Short circuit to the positive terminal of the temperature controller G2235
P0571 The combination indicates an incorrect signal received from the stop lamp switch A. A detailed check of the electrical circuit and the bulbs in the rear optics is needed.
P0606 Malfunctioning control module. This is a common mistake, so the user needs to test the microprocessor unit completely.
P0609 Supply voltage 2 on sensors and actuators
P0641 Open circuit voltage reference sensor A
P0651 Code P0651 reports a broken or damaged wiring; it is necessary to check the reference voltage of sensor B
P0670 Fault in the electrical circuit of the first glow plug. The reason may be a malfunction of the module itself.
P0671 Failure on the power line of the glow plug installed in the first cylinder. With such a problem, a green spiral can burn on the tidy.
P0685 Open or damaged electrical circuit of the main relay J271
P0688 Code 0688 for Volkswagen 2007, 2008 and other years of release appears when the main relay circuit breaks. The control unit has detected a malfunction in the load circuit. The user needs to make a detailed diagnosis of the J271 device.
P0693 Short to ground in the fan control circuit of the second motor cooling radiator. To remove this code, a detailed check of the line operation is required.
P0706 The combination P0706 reports an incorrect pulse coming from the activated transmission controller
P0730 Incorrect gear ratio in the transmission control system
P0748 Failure or damage to the electrical circuit supplying the first pressure controller
P0778 Code 0778 reports a malfunction in the electrical circuit supplying the second pressure regulator.
P1002 Code 1002 appears when there is a failure in the electrical circuit of the nozzle of the eleventh cylinder. Detailed testing of the N301 is required.
P10A0 Intake intake flap actuator: electrical malfunction
P1042 Malfunction in an electric circuit of a power supply system of nozzles In
P1128 The control unit recorded a lean mixture in the cylinders of the power unit, there were problems with its adaptation
P1161 Code P1161 is associated with a short circuit in the wiring supplying the G72 temperature controller. This refers to a device located in the intake manifold. The cause of the problem may be a broken cable or damaged insulation.
P1167 Code 1167 appears when an incorrect signal arrives from the mass air flow sensor G246
P1217 Code 1217 for Volkswagen 2006 and other years of manufacture indicates a short circuit to the "plus" power line that feeds the nozzle of the fifth cylinder
P1237 Breakage of the nozzle power line installed on the first cylinder. Verification of N30 is required.
P1245 Short to ground in the needle travel controller circuit G80
P1267 Output signal from the control range from the valve of the pump nozzle of the third cylinder
P1314 Code 1314 indicates a break in the wiring of the ignition control system in the first cylinder
P1401 Short circuit on the exhaust gas recirculation valve line. A detailed diagnosis of the N18 device is required.
P1409 Code 1409 is associated with a malfunction in the valve line of the first absorber
P1440 Open wiring supplying the exhaust gas recirculation valve N18
P1441 Error 1441 is related to a malfunction in the exhaust gas recirculation valve N18. The problem may be due to a broken wire or a short circuit to ground.
P1355 Break in the power line in the ignition control system of the first cylinder
P1503 Incorrect signal at the DF generator terminal
P1516 Open or damaged valve circuit of the intake manifold geometry change system N156
P1517 Malfunction in the power supply line of the main relay J271
P1526 Invalid signal detected on the fuel metering pump meter line
P1592 Wrong ratio of height controller and boost pressure signals
P1602 Code 1602 VAG COM on VWs in a sedan and other variations indicates a low voltage in the car's mains. A detailed diagnosis of terminal number 30 is required.
P1603 Malfunction of the control module
P1606 Problem related to the wiring of the ABS control module. The device may not transmit data on rough roads; malfunctions in its functioning are also possible.
P1624 Active request for the inclusion of an alarm indicator. An activation signal was sent, but for some reason the light did not work.
P1637 Faulty data bus drive. The central switching module does not transmit messages to the control unit.
P1639 Wrong pulse coming from the ½ accelerator pedal position controller. There may be no reaction when you press the gas.
P1640 Malfunction of the control module. This breakdown code is common, so the user needs to test the operation of the unit in detail.
P1641 Code P1641 reports an error reading data from the fault memory of the microprocessor module of the climate system
P1643 The control unit could not read the information from the fault memory of the main switching module
P1650 Error 1650 is due to a lack of signal from the instrument cluster control module. It is necessary to check all the connectors and the integrity of the wires connected to the unit.
P1654 The microprocessor module could not read information from the instrument panel fault memory. It is possible that one of the contacts disconnected from the control panel or the connector is oxidized on the block.
P1664 Code P1664 indicates a failure in the electrical circuit for supplying a control signal to the pump injector valves
P1668 Malfunction of the wiring supplying the valve of the pump nozzle of the third cylinder. A detailed check of the N242 is required.
P1698 Microprocessor module could not read the data from the memory of the steering column control module
P1699 No signal from the steering column control module.
P1857 Code 1857 is associated with an error message received by the engine control unit The cause of the malfunction may be an increased load.
P1895 Malfunction of the transmission unit
P1945 Short circuit on the control module circuit of the first engine fan
P1946 Failure or incorrect operation of the control module of the radiator fan motor
P1988 Code 1988 is the result of a break in the wiring through which the fan relay of the third engine cooling radiator is connected. The user needs to check the device J752.
P2008 Code P2008 indicates a failure in the power circuit of the intake flaps
P2009 Code P2009 short to ground inlet flap
P2011 Failure or damage to the power line supplying the flaps of the two inlet channels
P2016 Short circuit in the circuit of the position controller of the intake flaps
P2080 The appearance of code 2080 is due to an incorrect signal from the refrigerant temperature controller 1. The user needs to test the G235 device.
P2100 Open or damaged electrical circuit of the gear motor of the throttle actuator
P2138 Invalid signal from the ½ gas pedal position controller
P2149 On the Passat BZB and other models, this combination appears as a result of an interruption in the power supply circuit of injectors B
P2294 Open circuit of the fuel pressure sensor circuit
P2426 A short circuit to ground is detected in the electrical circuit of the cooling valve for the exhaust gas recirculation system. Perhaps the contact has gone somewhere or the insulation layer of the wire is damaged.
P242A Sensor 3 exhaust gas temperature in the exhaust gas recirculation system (EGR), Bank 1 - electrical circuit failure
P2453 Diesel particulate filter (DPF), pressure sensor A - circuit malfunction
P2564 Decreased signal output from the position controller of the boost pressure regulator
P2700 On Volkswagen Golf BFQ and other models, this code indicates a malfunction of clutch A automatic transmission (automatic transmission). This may cause the vehicle as a whole to be less powerful. If traction is lost and this code appears, you need to check the operation of the transmission unit.
P3008 The P3008 combination indicates that the signal coming from the camshaft adjuster is out of range
P3052 Short to positive in the starter gear wiring. The control unit indicates a malfunction in terminal 50.
P3089 The combination P3089 (3089) appears in the event of a failure in the electrical circuit supplying the fuel pump electronics. The cause of the problem should be sought in the signal cable.
P3338 Fault in the electrical circuit supplying the glow plugs. The microprocessor module does not receive a signal from the device; its detailed diagnostics is required.
P02CB Low pressure in a turbocharger or discharge device
P068A Code P068A00 indicates a malfunction in the ADR switch installed on the brake servo. The problem is in the electrics, so you need to check the contacts and wiring.
P10AD Open or damaged circuit supplying the electromagnetic clutch of a mechanical compressor device
P10A0 Electrical malfunction in the inlet control flap drive mechanism. With such a problem, fuel consumption will slightly increase, and the engine will not be able to raise revs above 3 thousand per minute. Replacing control flap required.
P17BF Fault mechatronics robotic gearbox. It is necessary to diagnose in detail the pressure receiver installed in the gearbox.
P189C mechatronics error
P424A General Electrical Trouble Code
909F Break or damage to the power line that supplies the brake pad wear controller
C02D1 Faulty right lower deflector switch. A detailed check of the F182 device is required.
VW Sensor Failures
097 Solenoid break or speed sensor malfunction. With such a problem, Golf 19TDI, 14 AKQ and other models may have difficulty shifting gears. If OBD 2 diagnostics showed this code, you need to check the speed controller of the gearbox in detail, as well as the connection of the solenoid. In some cases, the problem may be with the transmission control unit.
515 Malfunctioning Hall Controller G40
B10001B (B1000) Malfunction or lack of signal from the front airbag controller. The cause of the problem may be damage or clogging of the contact elements. To prevent such a malfunction in the future, the pins of the connector can be covered with a special protective agent.
B104135 (B1041) Malfunction of the engine fluid level controller. Checking the sensor located in the cylinder block is required. Due to its breakdown, incorrect information about the amount of consumable may be displayed on the dashboard.
P119A Malfunction of the fuel pressure controller
P462F Circuit Damage or Failure in Exhaust Temperature Controller
467F Malfunction in the controller ½ position of the gas pedal. An incorrect signal is being sent to the module, which may be due to disconnected contacts.
P22D500 (P22D5) Malfunction of the turbocharger intake valve position controller. The control unit receives an incorrect signal about the sensor operation. If the device itself is serviceable, then it is necessary to test its wires and block. The controller must be located in the valve of the turbocharged unit.
P0088 Code P0088 indicates a malfunction in the front right wheel acceleration controller
P0101 appears when the signal from the mass air flow sensor is incorrect
P0106 Invalid pulse from the intake air pressure controller
P0108 Intake manifold pressure / air pressure G71 / F96, too high
P0118 The combination of P0118 indicates an increased pulse coming from the refrigerant temperature controller
P0191 Invalid signal from the fuel pressure controller G247
P0221 Code P0221 appears as a result of the control unit receiving an incorrect signal from the angle of rotation controller of the second throttle assembly
P0234 Code P0234 indicates a malfunction in the boost pressure sensor. A signal is too high for the control unit that is out of range.
P0237 Increased signal coming from boost pressure controller
P0299 Code P0299 or P029900 also indicates a malfunction in the boost pressure controller. In this case, the signal from the device is less than the lower threshold.
P0321 Code P0321 reports an incorrect signal from the engine speed sender G28
P046C Error code P046C (P046C00) is literally translated as "exhaust gas recirculation valve position sensor row 1 signal out of tolerance"
P0471 Code P0471 appears as a result of the control unit determining an invalid signal from the first pressure sensor G450
P0501 Incorrect pulse received from the vehicle speed controller
P0588 Code 0588 Indicates a malfunction of the airbag igniter sensor. This refers to the device N95, located on the driver's side.
P0720 Code P0720 appears when the wiring to the gearbox output speed controller is damaged. The user needs to make a detailed diagnosis of the G195 device.
P0721 Code P0721 indicates an incorrect signal from the output shaft speed controller
P0722 Malfunction of the gearbox output shaft speed controller. No signal is sent from the device to the control unit. A detailed check of the G195 sensor is required.
P0841 Malfunction of the first pressure sensor in the hydraulic system of the gearbox. The device receives an incorrect signal, which leads to malfunctions in the transmission.
Possible symptoms of a malfunction accompanied by the appearance of this code:
- the "Check" icon is lit on the dashboard;
- lack of response to pressing the gas pedal;
- gear shifting difficulties;
- inability to turn on a certain speed;
- on automatic transmissions, jerks and shocks may be felt.
P1063 Code P1063 reports an invalid signal from the fuel pressure sensor.
P1164 Code 1164 on engines B4, G 68, 2E and others reports a malfunction of the fuel temperature sensor. A detailed check is required on the G81.
P1171 Malfunction in the second throttle angle sensor G188. The device may be receiving the wrong signal. The reason may be the drive itself.
P1539 On the Volkswagen B4 and other models, the combination of 1539 indicates incorrect operation of the clutch controller. This refers to the F36 device. In practice, this problem may be due to an incorrect signal received from the sensor.
P2293 Code P2293 results from mechanical damage to the engine fluid pressure controller. It is necessary to check the sensor and the quality of its connection to the wiring.
P1556 Code P1556 appears as a result of leaving the allowable range of signals from the boost pressure sensor
P2014 Malfunction in an electric chain of the controller of position of shutters of exhaust shafts
P2113 Combination 2113 appears when the controller fails In the gas pedal position
P2121 Error 2121 in a car with a V70, VR6 engine and other versions reports a malfunction of the gas pedal sensor. Data coming from the device to the microprocessor module is out of range.
P2122 Code 2122 reports a malfunction in the gas pedal position controller. There may be dirt or moisture on the device's contacts. A malfunction may be accompanied by a reduced signal from the G79.
P2185 Code P2185 appears as a result of an increased signal coming from the refrigerant temperature controller at the output of the radiator device G83
P246F Exhaust Gas Temperature Sensor 4, Bank 1 - Range / Performance
P2563 Code P2563 appears when the position sensor of the boost pressure regulator is not working properly. Most likely, an incorrect pulse is coming from the device.
P22D5 Turbocharger intake valve position sensor failure
9481748 Malfunction of the high pressure controller of the air conditioner.
VW Lambda probe malfunctions
P0036 The code indicates damage to the power line of the heating device of the second oxygen sensor installed in row 1
P0037 The combination 0037 appears when a short circuit in the heating circuit of the second oxygen regulator to ground
P0050 The combination reports damage to the wiring of the heating device of the first lambda probe installed in the second row
P0130 Failure in the electrical circuit of the first oxygen controller installed in row 1
P0133 Malfunction in the first lambda probe installed in row 1. An error indicates that the response time of the device is too high.
P0134 Lack of activity from the first lambda probe installed in row 1. Most likely, the sensor itself is faulty.
P0135 Code P0135 appears as a result of a malfunction in the electrical circuit of the heating element of the first oxygen controller. The lambda probe is installed in the first row of cylinders.
P0136 Failure of the electrical circuit of the second oxygen controller installed in the first row
P0139 Low speed signal transmitted from the second lambda probe installed in the first row of cylinders
P0140 No signal from the oxygen sensor No. 2, installed in the front row
P0141 Code P0141 indicates a failure in the electrical circuit of the heating device of the second oxygen controller located in the first row
P1116 Open circuit of the heating system of the first oxygen sensor installed in the first row
P1118 Damage or breakage in the power line of the heating device of the second lambda probe installed in the first row
P1176 The control unit determined that the maximum control limit of the lambda corrector installed after the catalyst was reached.
P1180 Short to positive in the circuit of the linear oxygen regulator
P1185 Short circuit in the power wiring of the linear oxygen controller to ground
P2237 Code P2237 reports a broken circuit and an inappropriate signal current from the first oxygen controller installed in row No. 1
P2239 Short circuit to the positive terminal in the circuit supplying the first oxygen controller
P2243 The code indicates a break in the wiring that connects the first oxygen controller installed in row 1
P2251 Open or damaged ground wire of the first oxygen controller installed in row No. 1
P4096 Fault in the electrical circuit of the first oxygen sensor installed in the second row
P2196 The control unit receives a signal about re-enriched combustible mixture from the oxygen sensor. This refers to the device number 1, located in the first row.
P2626 Malfunction of the linear oxygen sensor installed in the first row. The problem is the wrong signal coming from the device, so wiring diagnostics are required.
00525 Malfunction of the oxygen sensor G39
08598 An error may occur in the form of code 008598. The combination indicates a malfunction in the operation of oxygen controller No. 1 installed in the first row. A malfunction can lead to leaner air-fuel mixture.
16518 Lack of activity of the first oxygen sensor installed in row 1
17598 Invalid voltage reference for linear oxygen sensor
18675 Break or damage to the wiring supplying the first oxygen controller. This refers to the device installed in row 1. The control unit clarifies that the problem is related to the reference voltage.
Description of VW decimal codes
00003 Malfunctions in the operation of the control unit. A detailed diagnosis of the device is required, since there can be many causes of a malfunction, ranging from oxidized contacts to crashes in the program.
00010 The error can be displayed as a combination of 000010. Literally, the combination translates as "adjusting the position of the intake camshaft is too slow." The engine of the car can unstably idle. The cause of the problem, as a rule, is either a phase-shift valve or a phase-shifting clutch. Sometimes a malfunction is the wear or damage of the chain connecting the shafts.
00017 Malfunction of the executive electric motor of the rear left flap of the heating system for the space near the legs
00022 The code may appear as a combination of 000022. An error indicates a malfunction in the operation of the actuator motor of the right warm air damper. This refers to the element located at the rear of the center console.
00048 Malfunctions in the functioning of the left temperature controller of the heat exchanger G306
00135 Faulty front left wheel acceleration controller
00142 Malfunction of the valve damping adjustment front left wheel
00229 Incorrect pressure in the engine cooling system, possible causes of the problem:
service life of antifreeze is over;
one of the lines of the cooling system is damaged, which led to a leak of consumables (possibly weakening the clamps);
thermostat breakdown;
damage to the coolant expansion tank.
00258 On Volkswagen Bora 2009 and other models, this code indicates a malfunction in valve 1-N88
00260 Malfunction of the second solenoid valve N89
00262 Problems in the operation of the solenoid valve 3-N90
00275 The control unit has detected a malfunction in the exhaust valve ABS. This refers to a controller installed in the rear right brake circuit. Diagnostics of the N135 sensor is required.
00281 The speed sensor has failed or the control unit is not receiving a signal from it. It is necessary to check the operation of the electronic controller connected to the gearbox. The cause of the problem may be damage to the wiring or disconnection of the contact.
00282 Malfunction of the throttle control
00283 Failure of the front left wheel speed controller; check wiring and contacts
00285 Malfunction of the speed controller mounted on the front right wheel
00287 Malfunctions in the ABS sensor. A detailed check of the controller mounted on the rear right wheel is required. The speed controller G44 is missing or there is no signal coming from it.
00290 The control unit has detected a malfunction in the speed controller mounted on the rear left wheel
00300 Transmission fluid temperature controller malfunction in gearbox. Detailed diagnostics of the G93 device is required.
00369 Malfunction of the front right shock-absorber. The device works too softly, the spring may be damaged.
00406 Malfunction of the Hall controller of the electric motor of the sunroof
00435 On 20TDI, DRL, and other engines, this code indicates a malfunction of the parking sensor. This refers to the controller mounted on the front bumper on the right. A detailed diagnosis of the internal regulator G333 is required.
00446 A low voltage has been detected in the vehicle electrical system, which has limited the operation of the electronics or control unit. It is necessary to check the generator regulator relay and the battery.
00447 Limitation of the operation of one or more systems as a result of increased voltage in the electric network of a car
00457 On cars 2001, 2010 and other years of production, this OBD code indicates a problem in the operation of the onboard network control module. Detailed diagnostics of the J519 device is required.
00470 Problems in the operation of the data bus. Detailed diagnostics of digital interfaces and the control unit are required.
00474 The engine blocker control module does not send a signal to the microprocessor unit. Lack of communication can be caused by various reasons, from poor contact to a faulty immobilizer antenna. With such a problem, difficulties in starting the engine are possible. If the malfunction appeared after installing the anti-theft system, it is necessary to install the bypass block module.
00476 On cars 1997, 2000 and other years of production, this is a malfunction of the fuel pump control unit. You can independently identify this error, since when it appears, the engine does not start.
00513 Malfunction of the engine speed controller G28
00515 Fault Hall Controller G40. A complete check of the sensor is required, starting from the wiring of the contacts and ending with the wiring check.
00516 Problem in the operation of the throttle switch, the engine is unstable at idle
00518 The microprocessor has detected a malfunction in the throttle potentiometer G69
00520 There can be two reasons for the problem - either it is a malfunction of the air mass meter G70, or the potentiometer sensor G19
00530 Malfunctions in the operation of the throttle control potentiometer. The cause of the problem is the G88 device, therefore, a detailed diagnosis of this part is required.
00532 The power supply voltage does not match the standard rating. The cause of the problem may lie in the common on-board network, or on a certain circuit. First you need to check the battery and generator. If the diagnostics showed that the voltage is in the acceptable range, then testing of each wire connected to the microprocessor is required.
00533 Malfunctions in the idle speed control system. Sensor diagnostics required.
00537 Literally, this DTC can be decrypted as "lambda regulation". Most likely, the reason is the malfunctioning of one of the oxygen controllers.
00542 Malfunctions in the G80 injector needle stroke controller
00545 The electrical connection of the power unit and transmission is broken
00562 Incorrect operation of the temperature and lubricant level controller G266
00564 The error code can be displayed as a combination of 000564. On VW G63, 18 Turbo AEB, 1F and other engines, this code indicates a malfunction of the automatic gearbox selector. With such a problem, difficulties with gear shifting are possible.
00565 An error can be displayed in the format 000565. The control unit reports a malfunction of the Climatronic rear control and display panel (Climatronic). The user needs to make a detailed diagnosis of the E265 module.
00566 Improper power steering
00573 Malfunctions in the controller of the moment of resistance to rotation. The user needs to perform diagnostics and check the integrity of the contacts on the G269 device.
00575 Wrong intake manifold pressure
00588 Malfunction of the electrical circuit or the squib of the airbag installed on the driver's side. The problem may be accompanied by a burning indicator on the dashboard.
00589 Failure or lack of contact with the squib mounted on the first airbag on the passenger side
00591 Malfunction in the switching device of the lock on the driver's safety strap. Detailed diagnostics of the E24 device is required.
00652 Malfunction of the transmission control system
00655 On the Passat B4, B7 and other models, this code indicates a malfunction in the operation of the igniter of the tensioner tensioner device. This refers to the product mounted on the front passenger seat. The user needs to diagnose device N154.
00664 Malfunction of the fuel gauge
00665 Malfunction of the warning indicator indicator about unfastened safety straps. The error can manifest itself in the form of code 000665. It is necessary to check the operation of device N19. The problem may be the oxidation of the contacts on the bulb power wiring.
00668 Incorrect voltage in the electrical system. The control unit reports problems with the operation of terminal No. 30.
00768 The control unit reports an incorrect operation of the temperature controller of the rear heat exchanger. The combination may appear in error video 000768. Detailed diagnostics of the G154 device is required.
00770 The microprocessor module reports a malfunction in the antifreeze temperature detection sensor. This refers to the device located at the outlet of the radiator.
00771 Malfunction of the fuel controller G. Diagnostics of the sensor is required, its contact with the vehicle electrical system.
00772 F22 engine fluid pressure controller failure
00773 Breakage or lack of contact with the oil pressure sensor G10
00774 Malfunction of the ride height controller G76, installed on the rear left
00775 Breakage or lack of contact with the ride height sensor G77 mounted on the rear right
00776 A similar problem with the G78 controller, located on the front left
00777 Malfunction of the G79 sensor mounted on the electronic gas pedal
00778 Failure or lack of contact with the G85 controller, fixing the steering angle.
00792 Malfunction of the pressure controller in the climate system circuit
00801 Error can be displayed as a combination of 000801. A malfunction indicates problems in the operation of the high pressure controller for the electromagnetic coupling F118
00812 Breakage or incorrect operation of the switch solenoid coil of the brake pressure valve. A full check of the F84 device is required.
00819 Malfunction of the high pressure controller G65. With such a problem, incorrect engine operation is possible. A detailed sensor check is required with all wires and connectors. Sometimes the cause of the problem is damage to the insulation layer on the conductor supplying the sensor.
00833 The microprocessor module does not receive a signal from the windshield heating activation system
00849 Faulty or disconnected terminal S of the ignition switch and starter mechanism D
00883 Malfunction of the ignition switch and starter mechanism, the reason is in terminal D
00898 Invalid control pulse entering the air conditioning compressor
00907 Load regulator tripped; microprocessor module verification required
00924 Faulty relay optics cleaning system. Detailed diagnostics of the J39 device is required.
00928 Malfunction in the drive unit of the central lock. This refers to a lock installed on the driver's door.
00968 Malfunction of the right turn indicators
01025 Errors in the operation of the emergency lamp control system
01027 Failure or absence of a signal from the warm air supply fan. This refers to the rear device V47.
01043 Invalid software version in the control unit. You may need to update the firmware of the module, for this you will have to contact specialists.
01044 Incorrectly encoded engine control module
01045 On Volkswagen t4 2012 and other years of production, this code appears as a result of a malfunction of the Tiptronic switch. Perhaps the problem lies in the selector of the transmission unit, but it can also be in the gearbox control unit.
01056 Literally, the code translates as "purpose: equalization charge". The problem is wiring, so you need to start the diagnosis with the battery and generator.
01077 Failure or malfunction of the brake booster vacuum controller
01087 Literal translation of the error - "basic settings not completed." Most likely, the cause of the problem is the motor control unit.
01089 Faulty latch switch. The error can appear in the form of code 001089. The problem is typical only for vehicles in the back of a convertible. The control unit detected a malfunction when the car's roof was folded.
01119 Missing or incorrect transmission detection signal arriving at the microprocessor module. The cause of the malfunction may be damage to the wiring or malfunction of the transmission control unit. There may be a malfunction in one of the sensors.
01130 The anti-lock braking system is on. The cause of the problem may be a malfunction of the ABS control module, as well as poor contact.
01134 No impulse from the alarm sound device. Most likely, the cause of the problem is the siren. If the circuit of the device is equipped with a fuse, then the element must be checked. The problem may be disconnecting the contact.
01135 Malfunction in the controller of protection of salon. Perhaps the cause of the problem is the incorrect adjustment of the sensor sensitivity parameter. In addition, the malfunction may be a defect in the connector.
01139 Malfunction in the central locking switch, the problem is the device located on the front passenger door. It is necessary to test the contacts and wiring, if they are intact, then the product must be replaced.
01165 Malfunction of the throttle control module J338
01166 Invalid signal coming from the torque system of the power unit.
01176 Malfunction of the ignition key. Most likely, the cause of the problem is the immobilizer. A detailed diagnosis of the engine blocker is required.
01186 The control unit reports a malfunction in the Executive electric motor of the rear flap
01192 Malfunction in the torque converter lockup clutch. The problem appears on vehicles with automatic transmission. Most likely, the torque converter itself is faulty, but other transmission components must also be checked.
01207 Malfunction in the control module of the auxiliary heater J364
01221 Malfunction of the driver side impact airbag controller
01222 Malfunction of the side airbag shock controller installed on the front passenger side. It is necessary to check the operation of the device G180.
01237 On Volkswagen Bora and other models, this code indicates a malfunction in the fuel shut-off valve. A detailed diagnosis of the N109 device is required.
01217 Malfunction of the squib mounted on the driver's side airbag. The reason must be sought in the wiring or sensors.
01218 Defective igniter mounted on the side of the front passenger side airbag. Detailed diagnostics of the N200 are required.
01237 Failure of the fuel shutoff valve N 109
01249 On a Volkswagen Lupo or on a car with engines V16, V70 and others, this code appears when there is a malfunction in the nozzle of the first cylinder. To throw an error, it is recommended to clean the device.
01273 Malfunction of the supply fan V2
01274 Malfunction of the Executive electric motor of the air intake flap
01276 The control unit detected malfunctions in the hydraulic pump device of the anti-lock system. The first thing to do in such cases is to check the contacts on the V64 mechanism.
01299 Malfunction of the data bus diagnostic interface J533. A detailed check of the connector and all its contacts is required.
01304 The control unit indicates a malfunction in the car radio. The cause of the problem may be a malfunction of the antenna, as well as damage or disconnection of one of the connectors. A detailed check is required. This problem is not critical, so the use of the car is allowed.
01305 Malfunction in the data bus information command system Infotainment. Diagnostics of all contacts and microprocessor loops is required.
01309 Malfunction of the power steering control module. It is possible to turn off the unit due to vibration or damage to the contacts on its connector.
01314 Lack of communication with the engine control unit
01315 Gearbox failure. The problem is due to the lack of communication between the microprocessor and the transmission control module.
01316 Communication failure with the brake control unit
01317 Lack of communication between the control module of the motor and the instrument cluster
01328 Faulty digital data bus Comfort unit
01329 Data bus comfort control module operates in emergency mode
01330 Faulty central comfort control module J393
01331 Faulty driver's door control unit
01336 Malfunctions in the data bus of the comfort unit. A detailed check of the digital interface and testing of all contacts and wires is required.
01400 Malfunction of the ride height control system
01406 No flame formation in engine cylinders. If there is no ignition, the power unit will not start. The user needs to test all components of the ignition system.
01413 Failure or incorrect operation of the metering pump device V54
01415 On the Volkswagen Tuareg 005 and other versions for a malfunction of the circulation pump V55. First of all, it is recommended to check the power contacts of the device.
01423 Malfunction of the lateral acceleration controller G200
01426 Malfunction of the control panel on the steering wheel. Most likely, the reason is damage to the device itself or its poor contact with the on-board network. Possible oxidation of the contact elements on the block.
01486 Startup message for functional diagnostics of the system
01521 Failure of the air pressure controller installed in the tire. The sensor number is not indicated, so the user will have to diagnose all the regulators.
01542 Fault in the steering speed controller. The user needs to test the operation of the G202 device.
01592 Malfunction of the air pollution controller, refers to the sensor G238
01596 Malfunction of the electric motor for the supply air damper and air recirculation in the passenger compartment. Verification of V154 is required.
01598 Traction battery voltage is incorrect.
01674 On Volkswagen Passat B6 and other versions, this code indicates a malfunction of the ADR switch. The latter is located on the brake booster. To remove this error, you need to check the connector pins, maybe they are just dirty.
01809 Faulty electric motor of the executive system of the left flap air temperature
02039 Malfunction in the operation of the transfer case potentiometer. Detailed diagnosis of the G398 is required.
02054 Malfunction or breakage of the cross-axle differential lock control module. The user needs to diagnose the J647 device.
02214 Failure or incorrect operation of the emergency pressure switch installed in the tires
02236 Malfunctions in the operation of the right fixed headlight of the adaptive light system, the M52 mechanism must be checked. A possible cause may be a malfunction of the bulb or a damaged contact.
02251 The control unit reports that the heating system is blocked. It is necessary to diagnose the operation of fuses and relays, it is also necessary to verify the presence of antifreeze.
02432 The microprocessor module reports an improper power supply to the left actuating electric motor of the hand brake
02433 Error in the operation of the power supply system of the right executive electric motor of the hand brake. Detailed diagnosis of the V283 is required.
02443 Control panel malfunction. This problem belongs to the category of electronic malfunctions, so first of all, you need to check all the connectors.
02546 Problems in the operation of the steering lock
02557 On VW B3 Mono, TDI 1.9 and other versions, this error indicates a malfunction of the steering angle control. The control unit recorded that the installation position of the controller does not correspond to the normalized parameters. Perhaps the problem is jamming the device.
02845 Error code reports a problem in the operation of the pointer function on the instrument cluster
02861 Malfunction in the electronic steering column lock system. The cause of the problem may be a breakdown of the safety device or relay. To clear the error, detailed wiring diagnostics are required.
03091 Malfunction of the sensor of the fan of temperature of salon. Contact oxidation or pin damage is possible. There is no periodic signal from the controller.
03444 Malfunction of the ignition switch, meaning a lock. Perhaps the problem is not in the structural mechanisms of the device, but in the immobilizer. The lock does not detect the signal from the key, as a result of which indicates a malfunction of the lock.
03803 Malfunction of the electric power steering angle controller
03200 Malfunction in the electric hand brake switch. A detailed check of the E538 device is required.
03263 Malfunction of the brake system. The reason should be sought in the handbrake sensor, as well as brake pads.
03288 Parking brake applied. The user must first check the operation of the sensor on the "handbrake".
03375 Faulty electric motor for power steering system. Most likely, the cause is a mechanical malfunction. It is necessary to check the integrity of the housing, as well as the quality of the contacts, damage to the coupling is possible. If the defect is serious, the motor must be replaced.
03430 Damage or short circuit of the terminal 30, the supply lamp in the turning lights and brake lights
04260 The combination can be displayed in the form of code 004260. An error reports a malfunction of the inlet flap.
05399 On VW Digifant, AAF and other models, an error may occur as a six-digit code 005399. The combination indicates a malfunction of the main relay. In cars of 200 g and other years of release, the engine may not start with such a problem.
06079 Fault mechatronics robotic gearbox. First of all, check the hydraulic pump.
08194 This code may appear as a combination of 008194. A problem indicates a malfunction of the particulate filter.
08196 The intake shaft flaps do not close; check the elements for jamming.
08213 A malfunction can be displayed as code 008213. The problem indicates an incorrect operation of the inlet flap position controller. An incorrect signal is coming from the device, which may be due to electrics.
08518 Breakage of the power line supplying the nozzle A
08581 The code may appear as a combination of 008581. A problem indicates a malfunction in the G83 coolant temperature sensor. The reason should be sought in the controller itself, as well as in its contact with the connector.
08825 The engine control unit has detected an air leak in the intake system. Diagnostics of the integrity of all highways and pipe is required, the weakened clamps must be tightened.
09571 Incorrect signal periodically coming from the regulator of position of the charge pressure sensor. The error is not permanent.
10062 Malfunctions in the fuel pump
10065 Failure or absence of a signal from the flowmeter G70
10382 Cylinder head coolant valve malfunction
11730 Problems in the formation of air-fuel mixture
11836 Literally, the code translates as "turning off the cylinders". Diagnostics of all engine elements is required. A possible cause may be a malfunction of the components of the ignition system - candles or high-voltage wires.
11901 Malfunction of the boost pressure controller
12545 Malfunction of the electric motor of the drive valve of the intake manifold V157. The cause of the problem may be a short circuit for damage to the wiring.
16352 Unknown microprocessor module malfunction. A detailed diagnosis of the control unit is required.
16384 General engine malfunction. The cause of the problem may be in the sensors or pumps, you need to check the car in detail.
16396 In the front row, a shift in the valve timing is detected in the early direction. The control unit recorded that the nominal value of the parameters has not been reached.
16487 If this error appears on the dashboard display, the cause must be sought in the G70 air mass meter. The signal from the device is too high.
16497 On the Volkswagen T5 and other models, this code indicates an increased level coming from the intake air temperature controller
16500 Invalid signal from antifreeze temperature controller.
Possible malfunctions:
- failure of the temperature sensor installed in the tank or on one of the lines of the cooling system;
- damage to the wire supplying the sensor;
- dirt or dust on the connector;
- cable insulation fault.
16502 Increased signal from the coolant temperature controller
16555 lean mixture in engine cylinders
16556 Re-enriched air-fuel mixture in the engine
16672 Code 16672 (4120) literally translates to "cylinder injector 10-N300: short to ground"
16683 The signal coming from the boost pressure sensor does not correspond to the normalized parameters embedded in the control unit
16684 The microprocessor module detected misfires in one of the engine cylinders; the exact number is not indicated.
16685 The control unit detected misfire in the first cylinder of the engine
16687 The control unit has fixed one or multiple misfires in the third cylinder
16688 Misfire in the fourth cylinder of the engine
16705 Invalid pulse coming from the engine speed controller G28
16706 Lack of signal from the engine speed controller
16804 Decrease in efficiency in the operation of the catalytic system in the front row
16825 The engine control unit recorded a decrease in throughput in the operation of the gas tank ventilation system
16839 On the US Passat AWM 1989 and other years of production, this code indicates a serious leak in the fuel tank ventilation system
16885 Invalid signal coming from the car drive speed controller
16955 Incorrect pulse detected on the brake light switch line.
Possible causes of the problem:
- failure of the fuse or relay optics;
- damage to the wiring in the area from the brake pedal to the rear lights;
- oxidation of contacts in the fuse box;
- damage or deterioration of insulation on the power supply line of stop lights;
- malfunction of light sources installed in the taillights.
17069 Break or damage to the wiring of the main relay J271
17077 Short to ground in the second radiator fan control circuit
17090 Invalid signal received from F125 upstream gear controller. A check of the sensor and its wiring is required.
17526 Break in the power line of the heating system of the second lambda probe installed in the first row
17536 At Volkswagen Golf 5 and other versions, this code indicates a depletion of the mixture in the system of its formation. The error reports a malfunction in the first row of cylinders. There were problems with the adaptation of the mixture under load.
17549 Invalid load accounting data
17564 Short circuit to the positive terminal or open circuit of the pressure sensor in the intake manifold. The user needs to check the operation of the device G71.
17573 On Volkswagen T5, CDI engines error 175 73 and other models, this code indicates a re-enrichment of the mixture in the first row of cylinders. The control unit recorded failures in the adaptation of the air-fuel component in the first range.
17656 Invalid injection timing control range
17669 Malfunction associated with the operation of the valve of the pump injector of the first cylinder. A signal is received from the device that goes beyond the control limits.
17675 Invalid signal out of range of the valve pump injector third cylinder
17699 Decreased signal output from the refrigerant temperature controller at the output of the radiator device G83
17756 Open circuit at the first ignition terminal
17831 On the Volkswagen Jetta 6 and other models, the literal designation of the code is "too low throughput in the secondary air supply system of the first row." The cause of the problem should be sought in the depressurization of the system and damage to one of the pipes.
17887 Mechanical malfunction in the vacuum system of the brake booster
17925 Fault in the main relay circuit. It is necessary to check the contacts of element J271.
17947 Invalid signal received from the clutch pedal controller. A detailed diagnosis of the F36 device is required.
17964 Faulty boost pressure sensor. The signal coming from the device is much lower than the permissible parameter.
17967 Error in the basic installation of the throttle control module
17970 Upper limit of the fuel pump dispenser N146
17978 A blocking of the control module by the motor has occurred. With such a problem, difficulties with starting the power unit are possible. Blocking the module could occur as a result of malfunctions in the immobilizer.
18001 On VW AEE, Polo 12 and other versions, this code indicates the absence of a signal in the height adaptation system. If this error appears on the screen, it may be related to the operation of the air suspension. To remove, check all sensors and controllers.
18011 General problem in the operation of the control unit
18017 This error indicates that the shutdown system worked as a result of the shock.
18033 Malfunction in the data bus. The transmission control unit sends incorrect messages to the microprocessor module, which the latter cannot decrypt. A possible cause may be a lack of communication or damage to the bus.
18034 A code indicates a malfunction in the drive data bus. The microprocessor module does not receive messages from the control unit of the transmission unit. It is necessary to check the gearbox and test all the wires connected to the device.
18044 The microprocessor module does not receive messages from the security system control unit. The cause of the problem may be pillow sensors.
18049 The microprocessor module could not read the fault data from the climate system control unit. Detailed testing of the device is required, including verification of its contacts and wires.
18057 No messages received from the ABS control module. Detailed data bus diagnostics required. It is possible to disconnect the contact or damage one of the contact tracks on the loop.
18062 Data from fault memory in instrument cluster required
18068 Short to ground in the fan control circuit of the first motor cooling radiator
18072 A failure in the wiring supplying the valves of the pump nozzles. The device does not receive a control pulse.
18080 Short to ground in the fan control circuit mounted on the first radiator. Damage to the wiring or breakage is possible.
18359 The combination reports a malfunction in the second fan in the cooling system. The problem is locking the device or having difficulty running.
18570 Invalid signal from the ½ gas pedal position controller
18602 Malfunctions in the operation of the dashboard control unit - difficulties occurred while reading information about malfunctions from the module
18609 The engine control unit recorded a lean mixture in the first row of cylinders at revs above idle
18613 General malfunction in the cooling system. To find the exact cause, you need to check all the components.
18617 Increased signal level coming out of the antifreeze temperature controller. This refers to the sensor installed at the output of the G83 engine cooling radiator.
37038 General error in the operation of the ECP system
53273 The code may occur in the form of malfunction 053273. For cars in 2014 and other years of production, an error indicates a lack of communication with the control module by the instrument cluster.
53285 This code may occur as error 053285. When it appears, the control unit is recommended to diagnose fault combinations in the J301 control module.
65535 General fault code of the control unit. The microprocessor module needs diagnostics, first of all you need to check its connector and wires.
VW Other malfunctions
P177D If this VAG error code is read using an ELM 327 adapter, it can be output as a combination of P 17 7D. The control unit (ECU) indicates a malfunction in the dual clutch gearbox.
P20EE Code P 20 EE indicates low efficiency in the operation of the catalytic system, the problem should be sought in the first bank
P30c000 (P30c0) Low fuel quality
U0103 Lack of communication with the gear shift control module. A possible cause may be poor contact or disconnection of the block from the transmission unit.
U0121 Loss of communication between the microprocessor-based motor control module and the ABS unit. It is necessary to check the integrity of all buses and connectors, to test the quality of the connection. A possible problem may be a malfunction of one of the units.
U0423 Malfunction of the control module of the instrument cluster, an incorrect signal is supplied from the device
U1017 On Passat B7 and other data models, the code indicates a loss of communication sequence for second-class devices. Exact equipment is not indicated, so you will have to check all the wires connected to the microprocessor.
U1025 Loss of communication sequence for second-class devices. In other words, the problem must be sought in electronics and wire damage.
U111100 (U1111) Literally, the code U1111 is translated as "limitation of work due to the lack of a message".
With such a malfunction, you need to perform the diagnosis:
- all connectors and connections connected to the control unit;
- circuit integrity;
- gateway module
- the main unit of the comfort system;
- steering column control module.
U111300 (U1113) Error U111300 stands for functionality limitation due to received message
U101F00 (U101F) Faulty brake control module. The causes of the problem can be many, ranging from poor contact of the sensors and ending with a lack of fluid in the expansion tank.
P130A00 (P130A) Arbitrary shutdown of engine cylinders. The manufacturer does not provide accurate information to resolve this problem, so the user will have to independently diagnose the power unit.
IN 02 Maintenance reminder for Passat B3 and other Volkswagen models
L01 The combination indicates a malfunction in the cruise control system, its activation is not possible. If everything works in a car, then check the functionality of the microprocessor module. To eliminate the cause on engines 2E and others, it is necessary to diagnose the operation of the switch on the steering wheel.
0522 General malfunction in the powertrain control module
4043 Short to positive terminal of pneumatic control valve of injectors N212
4500 Short circuit to a positive terminal or break in the wiring supplying the antifreeze temperature sensor
008E Code 008 appears as a result of a malfunction of the wheel damping adjustment valve installed in the front left to the
012 This code for cars 2003 and other years of release indicates problems in the operation of the malfunction indicator. The lamp is on, it is necessary to test the diode itself, as well as its wiring.
441 Lack of pressure in the fuel tank. The cause of the problem may be a malfunction of the adsorber.
462 On VW TD 2005 and other model years, this code indicates a malfunction in the throttle control module
513 Malfunction of the climatronics system. To clear the error, check the quality of the connections of all components.
520 Malfunctions in the air mass meter. The user needs to test the operation of the potentiometer G70.
525 Lambda probe malfunction G39
537 Malfunction of the oxygen control system
575 Turbine malfunction, control unit fixes its insufficient boost. A red indicator may light on the dashboard. To determine and correct the error, it is necessary to diagnose the turbocharged unit.
Posted by: koreykoreygolae0270229.blogspot.com
Source: https://www.automotive-manuals.net/vw-fault-codes/
Post a Comment for "1948 Cadillac Series 76 Stock Front Suspension Diagram"